thermal capacity

Articles About thermal capacity


Articles are sorted by RELEVANCE. Sort by Date.

1 The Fundamentals of Specifying and Selecting Gear Drives (December 2012)

Gear drives deliver power to industrial equipment such as bulk material conveyors, mixers, pumps and paper mills. The reliability that translates into greater uptime and profitability begins by specifying and selecting the proper drives for these critical applications.

2 Is Splash Lubrication Compatible with Efficient Gear Units for High-Speed Applications (October 2015)

A thermo-mechanical model of a splash lubricated one-stage gear unit is presented. This system corresponds to a first step towards the design of a hybrid vehicle gearbox that can operate up to 40,000 rpm on its primary shaft. The numerical model is based on the thermal network method and takes into account power losses due to teeth friction, rolling-elements bearings and oil churning. Some calculations underline that oil churning causes a high amount of power loss. A simple method to reduce this source of power losses is presented, and its influence on the gear unit efficiency and its thermal capacity is computed.

3 Load Capacity and Efficiency of Grease-Lubricated Worm Gears (September 2014)

Varying installation requirements for worm gears, as, for example, when used in modular gear systems, can necessitate grease lubrication - especially when adequate sealing for oil lubrication would be too complex. Such worm gears are being increasingly used in outside applications such as solar power plants and slew drives. While knowledge about the operating conditions is often appropriate, the basic understanding for load capacity and efficiency under grease lubrication is quite poor. Investigations done at FZG and sponsored by FVA/AiF are shown here to give an impression of the basic factors of load capacity and efficiency. The results of the investigation indicate a satisfying quality of calculations on heat, load capacity and efficiency based on characteristic parameters of the base oil with only slight modifications to the methodology known from DIN 3996 or ISO TR 14521.

4 Finite Element Method Based Analysis of Planetary Gear Systems Considering Backlash and Manufacturing Deviations (June 2018)

The load carrying capacity of gear transmissions depends strongly on design, material and operation conditions. Modern analysis methods, e.g. finite element analysis (FEA), consider the above parameters with more or less sufficient accuracy. Yet it remains an ongoing challenge to account for backlash and manufacturing errors, despite a definite need to do so.

5 Evolution of Worm Gear Standards and their Consequences on Load Capacity Calculation Approach (September 2014)

Beginning with a brief summary and update of the latest advances in the calculation methods for worm gears, the author then presents the detailed approach to worm gear geometry found in the revised ISO TR 10828. With that information, and by presenting examples, these new methods are explained, as are their possibilities for addressing the geometrical particularities of worm gears and their impact upon the behavior and load capacity of a gearset under working conditions based on ISO TR 14521 — Methods B and C. The author also highlights the new possibilities offered on that basis for the further evolution of load capacity calculation of a worm gearset based on load and contact pressure distribution.

6 Power Loss and Axial Load Carrying Capacity of Radial Cylindrical Roller Bearings (June 2013)

This paper is intended to enlarge the application range of radial cylindrical roller bearings by means of a more precise determination of thrust load capacity and more cost-effective design.

7 The Importance of Thermal Protection for Torque Motors (August 2015)

When talking about high-end machining or manufacturing applications that include direct-drive technology, one of the key advantages of utilizing this particular transmission method is its endurance. Because of the very nature of direct-drive motors they are able to operate at peak performance levels indefinitely — without any kind of wear or aging — as long as the motor isn’t pushed past its capacity. Unfortunately, because this isn’t a perfect world, unexpected things can happen which can cause the motor to overheat. Whether the heat source is due to a parameter being input incorrectly, or an unexpected external force causing more resistance than expected — it is important to have certain forms of thermal protection in place. Since torque motors are built in such a way that they cannot be repaired and yet maintain their efficiency, it is vital to prevent any overheating — thus precluding the need to purchase a new one.

8 Thermal Growth Issues and Solutions for Shaft Couplings (August 2018)

Many refineries and chemical plants are built with large pieces of rotating equipment in an outdoor setting exposed to the elements. The author has been researching thermal growth issues for decades across North America.

9 Thermal Analysis and Optimization of Gearboxes by Simulation (December 2018)

With the increasing mechanical power capacity of gearboxes, the thermal power limit tends to become the limiting factor. To achieve a balanced system, the gear unit needs extra cooling. Using a fan that is mounted to a fast rotating shaft is a common solution. For this solution an optimal design is investigated.