Articles About space junk
Articles are sorted by RELEVANCE. Sort by Date.
With the constant push for sustainable and environmentally friendly procedures on Earth, you'd think weâ™d apply the same rules high above it.
Motor technology thrives in aerospace/defense applications.
The performance of high-speed helical geartrains is of particular importance for tiltrotor aircraft drive systems. These drive systems are used to provide speed reduction/torque multiplication from the gas turbine output shaft and provide the necessary offset between these parallel shafts in the aircraft. Four different design configurations have been tested in the NASA Glenn Research Center, High-Speed Helical Geartrain Test Facility. The design configurations included the current aircraft design, current design with isotropic superfinished gear surfaces, double-helical design (inward and outward pumping), increased pitch (finer teeth), and an increased helix angle. All designs were tested at multiple input shaft speeds (up to 15,000 rpm) and applied power (up to 5,000 hp). Also two lubrication, system-related, variables were tested: oil inlet temperature (160â“250° F) and lubricating jet pressure (60â“80 psig). Experimental data recorded from these tests included power loss of the helical system under study, the temperature increase of the lubricant from inlet to outlet of the drive system and fling-off temperatures (radially and axially). Also, all gear systems were tested with and without shrouds around the gears.
Oil shear brake technology is the key to quick and reliable test stand development.
Free vibration and dynamic operation testing of hybrid gears at NASA Glenn Spur Gear Fatigue Test Facility; hybrid gears are compared to their steel counterparts.
In a research project at the Vienna University of Technology, the KISSsoft design software was used to check a new drivetrain concept and the micro-geometry of the bevel gear stage for a UAV (unmanned aerial vehicle).
Modern aircraft, missiles and space vehicles employ a large number of electric motors and actuators. While the basic design of these motors is in many respects very similar to that of their automotive and industrial counterparts, motors for aerospace applications differ significantly in some areas.
It was recently announced that the planet Mars has at least one thing in common with planet Earth: all good things come to an end. In this case, the good thing is the recently announced and documented (Feb. 12) demise of the Mars rover Opportunity.
Moving around in open space is a cautious endeavor. Without the luxury of gravity, the slightest push can send you twirling in circles or, worse, tumbling off into the unknown. Every motion must be thought out and deliberate, all the more so because our bodies take that luxury into account.
Behind a thick sheet of unblemished glass that stretches from wall-to-wall, ceilingto- floor at Delta Gear, just south of a shop lined with ultramodern grinding machines whirring away, is Scott Sakutaâ™s aquarium.
The obsolescence of materials and processes in the manufacture of traditional DC brush gearmotors has necessitated the development of an upgraded DC brush gearmotor.
During the qualification campaign of the NIRSpec (near-infrared spectrometer) instrument mechanism, the actuator could not achieve the expected lifetime that had been extended during the development phase. The initial design could not be adapted to the requested number of revolutions during that phase. Consequently the actuator needed to be modified so that the function of the mechanism would not be endangered or, by extension, the overall function of the NIRSpec instrument. The modification included a change of the overall actuator designâ”internal dimensions, tolerances, materials, lubrication and assembly processâ”while keeping the interface to the mechanism, mass and function.
Fans of Arthur C. Clarke may remember a concept in his 1979 novel, The Fountains of Paradise, of an orbital elevator used to raise payloads from the ground to a satellite as a more cost-effective means of transporting material to outer space.
Volatile aerospace market keeps gear manufacturers guessing.
S.S. White Provides Twisting, Turning Power Transmission with Flexible Shafts
The complete Industry News section from the December 2013 issue of Power Transmission Engineering.
The complete Industry News section from the December 2012 issue of Power Transmission Engineering.
The U.S. Space Shuttle fleet was originally intended to have a life of 100 flights for each vehicle, lasting over a 10-year period, with minimal scheduled maintenance or inspection. The first space shuttle flight was that of the Space Shuttle Columbia (OV-102), launched April 12, 1981. The disaster that destroyed Columbia occurred on its 28th flight, February 1, 2003, nearly 22 years after its first launch.