motor drive inverter
Articles About motor drive inverter
Articles are sorted by DATE. Sort by Relevance.
New Opportunities and Technologies Allow AC Motors to Enhance Motion Control Applications.
This is the first of a series of articles on permanent magnet transverse magnetic flux motors - AKA step motors. These articles will be covering the development history and the various drive technologies used with these motors - both open and closed loop.
Zach Rountree's life would be a lot easier if his job site was closer to town. As the owner and president of Rountree Construction, he oversees an operation that pulls 200 tons of material an hour out of a remote lake in Stockton, Georgia. Big equipment demands three-phase power, but out in the remote timberlands of rural Georgia, only single-phase power was available.
Gearmotors handle harsh environments with digitalization, customization and improved service life.
Welcome to the Age of Information, where flexible, intelligent drive systems separate the haves from the have nots
Intelligent drive technology in the cowshed
One of the fun parts of the motion industry is involvement in popular movies! Motor specifications can be a bit rough: "I need to spin a 120-pound actor (and chair) 180 degrees in one-half second. He will be sitting up-right."
In Part I we explored various motor technologies used today for industrial and traction motor design. Here in Part II we will explore another motor option: reluctance motors.
The following article is a round-up of the latest linear motion product and industry news items featured at www.powertransmission.com and on social media.
The following article explains the commonly used paint components and methods within the gearmotor industry, with a focus on electrodeposition coating (E-Coat). These processes will be described in general, with a closer examination of the E-Coat applications steps. Some pros and cons of each method will be presented along with comparative test results showing the benefits of E-Coat.
Key technical drivers which can be addressed by advanced PM manufacturing technologies are, for example, the need for system downsizing in transmissions and differentials, the need for developing systems with higher power density and the strong NVH (Noise Vibration Harshness) requirements - especially for electrified transmissions or e-axle solutions.
Lower-cost motor technologies exist that can be an attractive alternative to neo-based BL PM motors - and are not subject to unpredictable supply chains
Standing in a factory or a warehouse, you're bound to notice machinery, whether it's a conveyor system that winds across the floor or large fans that hang from the ceiling. You may even notice automated guided vehicles or autonomous mobile robots carrying parts, driving themselves from one section of the building to another. These machines are good candidates for using high-efficiency gearmotors, especially if they're expected to run for long stretches at a time. If they aren't using high-efficiency gearmotors, then they may be costing more money than they should.
Special advertising section from the October 2019 issue of Gear Technology.
See our special advertising section focused on gears and gear drives from the September 2019 issue of Power Transmission Engineering.
How one gearbox manufacturer took an existing design and transformed it to meet the needs of this demanding environment.
Efficiency, power-loss reduction and enhanced performance are just a few examples of what the PT community wants from their gears and gear drives in 2019. Some companies are doubling down on service and assembly capabilities while other others are integrating components in an effort to increase flexibility and control.
Worm, bevel, and parallel shaft gear units were installed at two breweries to provide the necessary process control.
The complete Industry News section from the August 2019 issue of Power Transmission Engineering.
The complete Product News section from the August 2019 issue of Power Transmission Engineering.
Modern aircraft, missiles and space vehicles employ a large number of electric motors and actuators. While the basic design of these motors is in many respects very similar to that of their automotive and industrial counterparts, motors for aerospace applications differ significantly in some areas.
Efficiency, Size, Space and Mounting Requirements Highlight Customer Requests for No Compromise.
In the late 1940s, the U.S. auto industry started an exciting experiment and spent decades on it. One result came in '63, when the Turbine was introduced by Chrysler Corp., now a part of Fiat Chrysler Automobiles (FCA). In appearance, the two-door, four-passenger car looked like a regular car, but it wasnââ‚¬â„¢t. Under its sleek shell, the car had a jet engine.
The complete Industry News section from the June 2019 issue of Power Transmission Engineering.
Enhancing Safety, Quality, Delivery and Cost.
Chain and sprocket drives of one form or another have been driving machines and conveying materials for over a thousand years. The chain manufacturing industry has developed numerous types and sizes of drive chains. Although it is a mature form of power transmission, there are still many industrial applications for which drive chain is suited. It is economical, resistant to shock loads, easy to install, has the ability to transmit high torque, operates in hostile environments, and is efficient. Chain and sprocket drives are highly engineered and manufactured within close tolerances.
Yes, the headline is correct: Autonomous vehicles are not a new idea. In fact, in the 1950s, handsfree driving so interested General Motors engineers that they designed a concept car for it. And in 1956, at its own auto show, the GM Motorama, the automaker unveiled the car, the Firebird II.
The complete Industry News section from the April 2019 issue of Power Transmission Engineering.
Faulhaber motors help seek climate answers in deep-sea trenches
The complete Product News section from the March 2019 issue of Power Transmission Engineering.
Automate Show Examines the Integration of Robotics, Automation and Machine Vision, while Promat explores the latest in material handling technology.
The following special product news section examines the latest products and technologies in motion control.
Heavy industry. The phrase conjures images of mines and steel mills, of huge caverns underground, of cavern-like factories, of oldline companies operating heavy-duty machines for hightorque work. That's the image of heavy industry. Today, though, there's also another image. It's of an operator walking a steel mill's floor, looking at his smartphone or his tablet.
Most of us want to just instinctively squeeze a belt between a pair of pulleys to test the belt tension. What is not as instinctive is just how much force such a procedure can put on the shaft -- often significantly past the manufacturer's rated limits for small motors. This can cause damage to both the shaft and the bearings.
The complete Product News section from the February 2019 issue of Power Transmission Engineering.
Different motor types favor different application areas. No single style has advantages in all application spaces. Direct drive applications favor hybrid servos while high-speed, geared down applications tend to favor the conventional servo motors.
The complete Product News section from the October 2018 issue of Power Transmission Engineering.
Industrial mainstay adapts to remain relevant in a 4.0 world
IMTS 2018 had its fair share of machine tools, 3D printers and advanced robotics. Meanwhile, the East Hall â” home to Hannover Messe USA â” took a more systematic approach, highlighting the smart components and techniques that will be integral in developing the digital factory of the future.
Over the many years, there have been many technical papers and articles about which motor is the best. The short and sweet answer is - let's talk about the application. More recently a number of papers and articles have appeared that compared each motor's advantages and disadvantages in generic or specific terms. Many times, the methods used to drive and control these motors are not completely described due to the many control schemes available for use. A few articles focus on just the open loop step motor and the closed loop servo motor advantages and disadvantages in a laundry list format. This article is attempting to "drill down" into the reasons why and to describe how it is done.
A Look at Gear & Gear Drive Lubrication Performance Improvements
A Practical Comparison of Planetary and Orbitless Gear-Heads.
Schaeffler Touts System Solutions and Electrification Advancements at Detroit Symposium
The complete Product News section from the September 2018 issue of Power Transmission Engineering.
Gear drives focus on longevity, quality and customization.
Approximately one quarter of all servo motors around the world require some type of gear reduction in their applications. From large satellite dishes to precision medical devices, gearboxes boost torque and reduce speed for servos in order for them to be sized more efficiently. While gearbox fundamentals haven't changed much over the past 20 years, their effectiveness has improved significantly, driven mostly by the need to accommodate advancements in servo technology.
The skies are full of them in 2018 - drones flying around amusement parks, job sites and even your own backyard. There are drone racing leagues on ESPN, drones capturing wide angle shots over film locations and government drones keeping a bird's eye view on the Mexican/America border.
Health monitoring or condition monitoring has been used for many years on machines and in plants where the cost of an outage is high. It allows failures to be anticipated and maintenance or repairs to be scheduled for the least loss of production, as well as avoiding unnecessary periodic maintenance.
You may have noticed a lot of merger and acquisition activity lately in the power transmission industry. What does it mean?
Machinists Inc. is integrating the machinery, equipment and know-how of The Gear Works-Seattle Inc.
The complete Industry News section from the September 2018 issue of Power Transmission Engineering.
Modern drivetrains with voltage-source inverters not only offer advantages like, for example, variable speed operation, increased efficiency and higher dynamics, but also an increase in failures caused by induced parasitic currents.
JBT Corporation benefits from Kollmorgen Hygienic motor design in food and beverage application.
As manufacturers continually search for ways to cut costs and increase ROI, machine monitoring and predictive maintenance (PdM) solutions are an increasingly cost-effective way for plants and factories to help reduce process downtime.
Motor Operation Gets Big Boost from Smart Technology (Here's How to Take Advantage)
Elastic housing deformation by MESYS, plus new motors, actuators, gear drives and more.
The complete Industry News section from the June 2018 issue of Power Transmission Engineering.
While some organizations focus on real-world analytics and data collection for predictive maintenance, simulation tools and virtual prototyping can be another solution for motor efficiency.
If you can find that magic bullet that will reduce the machining process, you can achieve meaningful efficiency gains. It is imperative that check-weighers or in-motion weighing systems remain both accurate and efficient while attaining a consistently smooth operation because they dynamically weigh products as they move across the belt.
The technology continues to evolve in chain- and belt-driven systems
New servo drives, gear pumps, stepper motors and more.
The final installment in our Baldor Motor Basics series covers 50 Hz requirements, as well as motors wet or damp environments.
Microgears for some types of medical technology need to be inexpensively mass produced. But at the same time, they need to be both precise and reliable, even though their design lifetime is relatively short. Here's how microgears were developed for blood glucose measuring devices, insulin pumps for diabetics and other very small devices.
The complete Industry News section from the March 2018 issue of Power Transmission Engineering.
Explosion-Proof Motors in Division 2 Areas and DC Drive Fundamentals
In this work a physically based method for the tribological investigation of worm gears is presented.
Framo Morat and Dunkermotoren Produce Drive Systems for Automatic Guided Vehicles.
A worm drive is a geared power transmission device in which a worm meshes with a worm gear to transmit power between two non-intersecting shafts that are oriented at a right angle. The worm drive has been an active and challenging topic of technological study since Leonardo da Vinci (1452-1519).
Copper's continuing role in energy-efficient motor development.
Energy efficiency is for more than just motors. Here are some mechatronics companies making sure you get more bang for your buck when it comes to your power bill.
The latest mechanical power transmission products from Nord Drivesystems, Gearing Solutions, Ogura Industrial, Stafford Manufacturing, Rexnord, Portescap, Steinmeyer, Intellidrives, J.W. Winco and Zero-Max.
Failure to specify the proper motor for use in a hazardous location can have serious consequences - lost production, extensive property damage, and even loss of human life. Selection of the proper motor requires an understanding of Underwriters Laboratories' (UL) and National Electrical Code (NEC) class, group and division designations and the T code letters.
Amps, Watts, Power Factor and Efficiency; Approximate Load Data from Amperage Readings; Power Factor Correction on Single-Induction Motors.
Conservation through lighting alterations using different bulbs, ballasts and light sources is well understood and easy to achieve. The use of improved efficiency three phase induction motors has not been as accepted. There are a number of reasons why conservation efforts with motors have not been as popular.
Gearmotor manufacturers find new ways to push the envelope. (With Sidebar on new alternative to planetary gearboxes)
New HMI from Siemens, ITAMCO ramps up additive manufacturing, LM76 introduces new linear bearings, plus other new products from around the industry.
Part 1: There seems to be a lot of confusion about the voltage standards for motors and why they are structured the way they are. Part 2: The effect of low voltage on electric motors is pretty widely known and understood, but the effect of high voltage on motors is frequently misunderstood.
Faulhaber Provides Motor Technology for Pipe Renovation Projects
The complete Product News section from the September 2017 issue of Power Transmission Engineering.
This is an article about motors - preventive motor maintenance, actually. And something else - mechatronics. In today's high-tech manufacturing and industrial use environments, it is near impossible to talk about equally complex motor maintenance and repair-or-replace protocols without it.
Process Expo and Pack Expo Highlight the Latest Technology for Food & Beverage Applications.
As the old adage goes, "There is more than one way to skin a cat." In the early stages of any project, system designers are faced with choices; whether they are designing a new application or retrofitting an old one, they need to determine what is the most efficient, economical and practical way of completing the task at hand. Though there are usually at least two viable means to accomplish the task, the first step is always to review and weigh the merits of each option.
Highlights from some of the gear, gear drive, power transmission component, software, materials and related exhibitors at Gear Expo 2017.
Most of you who read this magazine have a close relationship with gears and gear drives. According to our surveys, 75% of you recommend, specify or buy them. It's a shame, then, that the majority of you will miss Gear Expo (Oct. 24-26 in Columbus, OH) this year.
The complete Industry News section from the September 2017 issue of Power Transmission Engineering.
How to Ensure Reliable Performance, Increased Efficiency and Lowest Total Cost of Ownership.
The latest tools and techologies in power transmission, motion control and related components.
A good deal of confusion exists regarding the factors that determine an industrial electric bill. The following information is presented to help sort out the various items on which billing is based, and to offer suggestions on measures to help control and reduce electric utility bills.
DC motors possess linear relationships that allow for very predictable operation. For instance, if enough voltage is applied across the terminals of a DC motor, the output shaft will spin at a rate proportional to that applied voltage. You can take the ratio of the applied voltage over the rated voltage and multiply that number by the no load speed and get the running speed.
Fans, blowers and other funny loads are addressend, along with RMS Horsepower loading.
Motor technology thrives in aerospace/defense applications.
Standardized calculation methods such as ISO 6336 and DIN 3990 already exist to determine the load distributions on gears inside a planetary gearbox, but by their very universal nature, these methods offer varying results depending on the gearbox design. Double helical gears, in particular, can benefit from more specific, complex algorithms to reach a maximum level of efficiency. Double helical gears interact with the rest of the gearbox differently than helical or spur gears, and thus benefit from different analytical models outside the standardized methods. The present research project describes the algorithm to determine the load distribution of planetary gearboxes with double helical gears.
The complete Product News section from the June 2017 issue of Power Transmission Engineering.
The complete Industry News section from the June 2017 issue of Power Transmission Engineering.
In the process of applying industrial drive products, we occasionally are misled into believing that we are applying horsepower. The real driving force is not horsepower - it is torque. This paper is developed to impart a deeper understanding of torque, its relationship to horsepower, and the types of loads we most frequently encounter.
This issue our Baldor Basics series continues with the topics of motor temperature ratings and metric motors.
If there are two things that are in tight supply in the industry, it's time and talent. Manufacturers are always pressured to do more faster, and the industry is producing fewer experts to help them do it, so the industry's had to get crafty and find what time-cutting procedures they can.
In today's highly competitive world, the better someone understands the advantages and benefits of direct drive technology, then the more they will have an advantage in machine building, giving them an edge over their competition.
Three electric motor repair facilities share best practices for utilizing copper in motor repair, and recommending new motors to replace older, less-efficient motors
The complete Industry News section from the March 2017 issue of Power Transmission Engineering.
A machine called Sub1 Reloaded solved a Rubik's Cube in 637 thousandths of a second in Munich.
This issue we cover frame sizes and two-speed motors in our continuing series of articles, courtesy of Baldor Electric, dedicated to motor basics.
I'm not able to get a good connection between the pulley and shaft in my drive assembly. Could you explain the various ways of connecting a pulley to a shaft to prevent the pulley from slipping?
This paper presents a joint project conducted by Ashwoods Electric Motors and Oerlikon Fairfield that uses planetary drives with an integrated electric motor. Current solutions used in production of off-highway vehicles rely upon large, heavy and inefficient brushed DC or induction motors, coupled to a planetary gearbox. This presents a number of challenges to the vehicle designers such as: limited vehicle range, limited space around the motor/drivetrain, and motor durability. The proposed integrated system utilizes an Oerlikon Fairfield Torque Hub, widely used in off-highway vehicles, and the Ashwoods first-to-market, interior permanent magnet motor. How these products are integrated, i.e. incorporating a brake solution, represents a market-changing product. Using interior permanent magnet (IPM) technology in the motor design means the motor can be up to 70% lighter, 70% smaller and 20% more efficient than traditional motors used in off-highway traction applications.
Beginning with this initial installment , and with the gracious permission of ABB/Baldor Electric, we are pleased to announce the beginning of a new series -- Baldor Basics: Motors. This is a collection of basicsdriven, motor-intensive articles authored by former Baldor engineer Edward Cowern, PE, a respected name by many in the electric motor industry. During his tenure at Baldor, Cowern - now enjoying his retirement - was tasked with producing a number of motor- and basics-related tutorials, primarily in response to a steady flow of customer questions regarding motors. Today's customers continue to ask questions and seek answers to address their various motor-related issues. As with Cowern's original introduction to the series, we hope you find these articles useful and would appreciate any comments or thoughts you might have for future improvements, corrections or topics.
Implementing a power-on-demand concept based on variable speed drives allows for energy saving in any application that involves pumps or hydraulic systems. And when used in combination with an intelligent wiring and communication system, relevant machine data can also be easily recorded - the basis for comprehensive power management.
Synchronous drives are especially well-suited for low-speed, high-torque applications. Their positive driving nature prevents potential slippage associated with V-belt drives, and even allows significantly greater torque carrying capability. Small pitch synchronous drives operating at speeds of 50 ft/min (0.25 m/s) or less are considered to be low-speed. Care should be taken in the drive selection process as stall and peak torques can sometimes be very high. While intermittent peak torques can often be carried by synchronous drives without special considerations, high cyclic peak torque loading should be carefully reviewed.
New things are invented for theater lighting all the time and theyâ™re usually big, expensive technology-driven devices. Itâ™s the simple things that make you wonder, âœWhy didnâ™t I think of that?â according to Ken Billington, lighting designer. The RSC Lightlock is a great example of this.
It's no secret that conveyor systems are the primary market for gearmotors, and so it shouldn't be much of a surprise that gearmotor manufacturers are looking for ways to cater to that market's needs. From Brother's new VFDs to Siemens' Simotics S-1FG1, a lot of the new solutions in the industry have their own unique quirks, but all fall into a few common veins.
When the need arises for linear motion or positioning, there are many choices. One can use an Acme screw, ball screw, rack & pinion, or belts. The cost of a linear motor solution is generally greater than a mechanical linear product, but when one needs highly accurate, repeatable, high-speed motion, then the answer may be a linear motor.
If youâ™re an electrical engineer you know how an electric motor works; if you arenâ™t, it can be extremely confusing. Therefore, hereâ™s the simplified explanation (or the âœhow an electric motor works for dummiesâ version) of how a four-pole, three-phase AC induction motor works in a car.
For the lubrication of open gear drives used in different industrial applications such as cement and coal mills, rotary furnaces, or where the sealing conditions are difficult, semi-fluid greases are often used in preference to fluid oils. For girth gear applications the greases are used with a splash or spray lubrication system. The selection of such greases influences pitting lifetime and the load-carrying capacity of the gears, as well as wear behavior
Increasing pressure on many fronts is compelling mine operators to thoroughly examine every phase of their operations. Fluctuating demand that whipsaws mineral prices, government-imposed environmental regulations and rising operating costs related to maintenance downtime all pose serious challenges for the mining sector. Add pressure from customers and stakeholders for more sustainable operations as well as union demands for higher wages, and you have a scenario that requires mine operators to exercise every possible option to achieve more efficient operations.
News about recent products in the Industry
Ernest Head (Arnie), CBS and technical sales representative at Motion Canada helped save a lumber industry customer time and money by adapting a bearing solution for another client. Hereâ™s how:
News about industry products.
Referencing a June 2014 Article, âœHigh Gear Ratio Epicyclic Drives Analysis,â by Dr. Alex Kapelevich: I have designed a small compound epicyclic gearbox with common planets. Sun = 10 teeth Planet = 14 teeth Ring Gear stationary = 38 teeth Ring gear output = 41 teeth profile shifted onto a 38 tooth pitch diameter. Carriers are simply cages for the planet alignment and location. According to your article, and according to my calculations and the prototype I have built, my inputto- output ratio is a reduction of 65.6:1. I am using a ~ VG1 viscosity grease and Nylatron materials for the gears and carriers.
Latest news on products.
In this centuryâ™s complex, ever- changing world of manufacturing, such capabilities as hardware and software expertise, effective location and distribution, business savvy and yes, even luck, are some of the cardinal requirements for running a successful business.
Without the sun, there would be no Earth and no life. However, our knowledge about our home star is still very limited. This is about to change. In 2018, the European Space Agency (ESA) will send its Solar Orbiter into space, equipped with a thick heat shield.
The performance of high-speed helical geartrains is of particular importance for tiltrotor aircraft drive systems. These drive systems are used to provide speed reduction/torque multiplication from the gas turbine output shaft and provide the necessary offset between these parallel shafts in the aircraft. Four different design configurations have been tested in the NASA Glenn Research Center, High-Speed Helical Geartrain Test Facility. The design configurations included the current aircraft design, current design with isotropic superfinished gear surfaces, double-helical design (inward and outward pumping), increased pitch (finer teeth), and an increased helix angle. All designs were tested at multiple input shaft speeds (up to 15,000 rpm) and applied power (up to 5,000 hp). Also two lubrication, system-related, variables were tested: oil inlet temperature (160â“250° F) and lubricating jet pressure (60â“80 psig). Experimental data recorded from these tests included power loss of the helical system under study, the temperature increase of the lubricant from inlet to outlet of the drive system and fling-off temperatures (radially and axially). Also, all gear systems were tested with and without shrouds around the gears.
Latest information about upcoming products.
Gearing is an essential component in conveyors. The material handling industry appears divided between those who favor high-end three-stage helical bevel gearboxes and those who rely on less expensive worm gearing. But thereâ™s an often over-looked alternative, the two-stage helical bevel gearbox.
U.S. manufacturers, such as food processors, face an unprecedented competitive environment and must look for ways to be profitable without negatively affecting the quality of finished products.
This three-part series on motor management best practices focuses on the importance of instituting a motor management plan as a necessity in effectively administering the electric motors in a facility. The goal of a motor management plan is to take advantage of opportunities for energy savings and increased productivity using energy efficient, reliable motors such as NEMA Premium efficiency motors, herein referred to as âœpremium efficiencyâ motors.
As with just about everything else in the manufacturing world â” and all which that universe entails â” it depends. After all, thatâ™s why the art of manufacturing is a process â” not a one-system-fits-all discipline. Yes, once that process has been properly designed and correctly implemented for a given manufacturing production need, it may well run like the astest, smoothest cookie-cutter-type operation ever devised.
As gear efficiency is improved in small steps, it is important to be able to distinguish actual improvements from scatter that can occur while testing. An FZG back-to-back gear test rig was used to investigate how the assembly and re-assembly of the same test setup affects the measurements. A spread in torque loss between one assembly and another of the same test setup were observed. Rig conditions also affected the spread in input torque. With knowledge of how the spread in torque loss varies due to assembly, test results could be distinguished between changes due to assembly and actual differences between tests.
Energy costs and downtime can be greatly reduced by instituting a motor management plan. Part II of this three-part series specifically addresses the establishment of a motor failure policy and the development of purchasing specifications. Part I addressed the general aspects of a motor management plan, including the first steps of creating a motor inventory and guidelines for motor repair and replacement. Part III will examine motor repair specifications as well as preventive and predictive maintenance.
News about latest products
This issue we take a long, hard look at motor efficiency, and you should, too. After all, electric motors used in industrial settings are the single largest consumer of electricity in the United States. Upgrading your electric motors is not only good for the environment, but itâ™s also good for your bottom line. Sure, saving electricity lessens the burden on our countryâ™s energy infrastructure. But it also saves you money in the long run.
A thermo-mechanical model of a splash lubricated one-stage gear unit is presented. This system corresponds to a first step towards the design of a hybrid vehicle gearbox that can operate up to 40,000 rpm on its primary shaft. The numerical model is based on the thermal network method and takes into account power losses due to teeth friction, rolling-elements bearings and oil churning. Some calculations underline that oil churning causes a high amount of power loss. A simple method to reduce this source of power losses is presented, and its influence on the gear unit efficiency and its thermal capacity is computed.
News From the gear Industry
The secondhand on the Doomsday dial ominously spins around the face, slowly but ever so surely inching the motor industry towards its inevitable terminus:
Reducing losses and increasing profits by instituting a motor management plan is what this series of articles is all about. Here in Part I, we discuss how to create a motor inventory and establish repair-or-replace motor guidelines. Subsequent topics in this three-part series will address (Part II) motor failure policies and purchasing specifications, and (Part III) repair specifications and preventive and predictive maintenance, respectively.
With advances in modern technology reducing demand for envelopes, manufacturers are finding it increasingly hard to justify investment.
Over the past few decades, energy efficiency in motors has become an ever-increasing concern for OEMs and manufacturers alike. With multiple energy bills mandating higher efficiency across ever-broader spectrums of motors, including the most recent Small Motor Rule by the Department of Energy, efficiency has become an essential consideration when choosing a new motor.
Tooth contact analysis (TCA) is an important tool directed to the determination of contact patterns, contact paths, and transmission errors in gear drives. In this work, a new general approach that is applicable to any kind of gear geometry is proposed.
When talking about high-end machining or manufacturing applications that include direct-drive technology, one of the key advantages of utilizing this particular transmission method is its endurance. Because of the very nature of direct-drive motors they are able to operate at peak performance levels indefinitely â” without any kind of wear or aging â” as long as the motor isnâ™t pushed past its capacity. Unfortunately, because this isnâ™t a perfect world, unexpected things can happen which can cause the motor to overheat. Whether the heat source is due to a parameter being input incorrectly, or an unexpected external force causing more resistance than expected â” it is important to have certain forms of thermal protection in place. Since torque motors are built in such a way that they cannot be repaired and yet maintain their efficiency, it is vital to prevent any overheating â” thus precluding the need to purchase a new one.
Experts gathered at the 9th CTI Symposium to discuss the challenges of reducing noise, improving energy efficiency and meeting the changing demands of the marketplace
The improvement of the energy efficiency of industrial gear motors and gearboxes is a common problem for many gear unit manufacturers and end-users. As is typical of other mechanical components, the radial lip seals used in such units generate friction and heat, thus contributing to energy losses of mechanical systems. There exist today simulation tools that are already helping improve the efficiency of mechanical systems â” but accurate models for seal frictional losses need to be developed. In this paper SKF presents an engineering model for radial lip seal friction based on a physical approach.
News about latest Products in the Industry
This paper presents a physically grounded calculation method to determine the efficiency of worm gear drives. This computation is based on the Institute of Machine Elements, Gears, and Transmissions (MEGT) tribological simulation, which can determine the local tooth friction coefficients (Ref. 1). With this knowledge other power losses such as the bearings, oil churnings and seals power losses can also be calculated.
One of the key challenges in the mining industry today is maintaining throughput in the face of ore grade quality that has declined by 40 percent in the last decade.
How would you compare the efficiency and capabilities of hybrid stepper motor actuators vs. can stack stepper motor actuators?
News from Around the Industry
Hi. My name is Renee. Iâ™m 12. You might remember me from about a year ago, when my dad wrote about me and the home-made motor project we did together (âœMake the Connection,â February 2014).
Enhancing production with â” and for â” less is the standing order in todayâ™s manufacturing world. Speeding up production while at the same time looking for ways, to cut, for example, energy costs, is a tricky equation with no single answer; where and how management goes about achieving that can take several paths.
Rosetta Mission mixes with Maxon, Kim K for one unforgettable photo
In recent years the estimation of gearbox power loss is attracting more interest â” especially in the wind turbine and automotive gearbox industry â” but also in industrial gearboxes where heat dissipation is a consideration as well. As new transmissions concepts are being researched to meet both ecological and commercial demands, a quick and reliable estimation of overall efficiency becomes inevitable in designing the optimal gearbox.
New products within the Industry
John Morehead, national sales manager of Crouzet Motors (Vista, CA), was bunkered down in his office in Palatine, IL surrounded at all points by ankle-deep snow from an unfortunately terrible Chicagoâ™s winter night.
The changing landscape of hydraulic drives is leading many fluid power specialists to quickly adapt to using variable speed pump drives. Optimum utilization of these drives requires, in many cases, additional system design considerations.
The use of motor current signature analysis (MCSA) for motor fault detection â” such as a broken rotor bar â” is now well established. However, detection of mechanical faults related to the driven system remains a more challenging task. Recently there has been a growing interest for detection of gear faults by MCSA. Advantages and drawbacks of these MCSA-type techniques are presented and discussed on a few industrial cases.
The motors might be small, but the big-brain technology driving these electrical wonders was on full display at the 2014 Small Motor & Motion Association Fall Technical Conference, convened November 4-6 in St. Louis, MO. SMMA, the manufacturing trade association (120 members strong) that tends to the best interests of the electric motor and motion control industries â” including manufacturers, suppliers, users, consultants and universities â” played gracious host to a wide array of presenters from an equally diverse range of sources â” from academia to the federal government. Like gears, motors are most everywhere, as evidenced by SMMAâ™s membership (consumer-, public interest-, national defense- and commercial-oriented) demographic which includes: appliance; transportation; medical equipment; office automation and computers; aerospace; and industrial automation. The associationâ™s mission: To âœserve as the principal voice of the electric motors and drives industryâ and to provide a forum to âœdevelop, collect and disseminate technical and management knowledge.â
A wide variety of companies displayed mechanical power transmission and motion control technologies at Pack Expo, held in November in Chicago. The event, which is the largest packaging and processing trade show in North America, attracted more than 48,000 attendees, according to show owner and producer PMMI. The four-day event included 2,352 exhibiting companies, an increase of more than 19 percent from the previous show in 2012.
According to the Department of Energy (DOE), more than half of all electrical energy consumed in the U.S. is used by electric motors. To address this, several years ago, the DOE conducted a technical study as to what could be done to raise the efficiency levels of âœsmallâ motors. After years of study and litigation, the Small Motor Rule (SMR) was passed that covers two-digit NEMA frame single- and three-phase ¼ through 3 horsepower motors in open enclosures.
EDITORSâ™ NOTE: âœThe Applications of Bevel Gearsâ is the excerpted third chapter of Dr. Hermann Stadtfeldâ™s latest book â” Gleason Bevel Gear Technology (The Gleason Works, Rochester, New York, USA; All rights reserved. 2014; ISBN 978-0-615-96492-8.), which appears here unabridged through the kind graces of Dr. Stadtfeld and Gleason Corp. Future installments will appear exclusively in Power Transmission Engineering and Gear Technology magazine over the next 12 to 18 months.
News from around the industry.
What is the recommended method of gripping a spinning shaft (with up to 130 hp of rotational energy) to install pre-tension thrust bearings and conventional thrust bearings (load = hundreds of pounds) when the shaft cannot have any high points because it must pass through an area of tight clearances to assemble? Will snap rings still withstand the harsh vibration of this environment?
News from the industry about new products.
News about new Products in the industry.
Electric motor-driven systems are the single largest enduser of electricity, accounting for over 40% of global consumption according to the International Energy Agency.
If you read only one article this issue, it should be Norm Parkerâ™s article on the Chinese bearing manufacturing industry. Parker is an engineer with General Motors, a true industry insider who has become a regular contributor to Power Transmission Engineering.
ContiTech and Wöhr Team up for Unique Residential Solution.
The complete Product News section from the September 2014 issue of Power Transmission Engineering.
The Formula Renault 3.5 is seen as a crucial stepping stone on the way into the premier class, the Formula 1. Ambitious racers do not just bring their talents - they also have highly efficient motors on board to control the throttle of their 530-hp V8 engines.
University lab's motor eliminates pricey rare-earth magnets.
There are three major types of reluctance motors: all three reluctance motors are non-permanent magnet, brushless motors. They are synchronous motors with a non-linear relationship between torque and current. The variable-reluctance step and switched-reluctance motors utilize the principle of magnetic attraction by inducing magnet poles within the soft-iron rotor, and by energizing a set of coils wound around stator teeth resident in the laminated stator. These two reluctance motors must be sequentially excited to achieve continuous, steady-state rotation. The design of all reluctance motors requires finite element analysis (FEA) software.
The complete Industry News section from the August 2014 issue of Power Transmission Engineering.
There are more brushless PM motors being made every day. These brushless PM motors are smaller in size -- i.e., less than 50 watts in power output found in hard-disk drives, CD and DVD players and many portable medical devices. Servo systems with brushless PM motors ranging from 50 watts to 50 kilowatts are now challenging the larger electric motor applications. A few manufacturers have pushed brushless PM motors above 200 kW.
This product focus highlights the latest technology in electric motors.
When I woke up this morning, my house was a comfortable 68Â°F, despite the fact that overnight temperatures in the Chicago area were close to freezing. I donâ™t often think about the blower motor that helps circulate the warm air from my furnace throughout my house, but today I was grateful for it...
Step motors come in many sizes and shapes. But they all share one item in common - each step motor type moves in discrete-degree steps. They react to a series of voltage pulses supplied by their basic controller, known as an "indexer." The step motor was the first to accept digital pulses, then move or rotate a prescribed amount without any feedback device. All step motors are position devices without the need to use any feedback devices. They operate primarily in an open-loop control scheme.
EECV in Rotterdam, the Netherlands, keeps on expanding and improving. In 2013 their transhipment of coal increased and they installed a new bucket wheel reclaimer with a capacity of 3,500 tons per hour. They chose a direct-drive system from Bosch Rexroth for this big bucket wheel. The drive system consists of a HÃ¤gglunds MB 1600 motor and a DUe drive unit.
This paper outlines the design considerations that go into construction of a drive system in order to explain the importance of specific data, why it is required, and where design freedom is necessary. Apart from loads and speeds, interface dimensions and site specific conditions are also needed. Deciding up front which gear rating practice to select can affect the torque capacity of the drive train by ~15%.
Recently I had a disturbing conversation with a colleague here at the office. During the conversation, it became clear to me that my co-worker -- a really intelligent guy whom I respect a lot -- had no idea how even the most simple electric motor works.
Video from Maxon Motors, Hannover Messe on our LinkedIn page and the NFPA annual conference on our Facebook page.
The complete Product News section from the December 2013 issue of Power Transmission Engineering.
A brief overview of the induction motor, including the basics of construction, performance and variable speed drives.
A discussion of the basics in DC drives, DC motors, AC drives, AC motors and synchronous motors.
This article describes the challenges involved in designing and implementing microstepping systems.
Dave Soma, the mechanical supervisor at Leland Olds Station, a coal-fired power plant near Stanton, North Dakota, says he and his maintenance team care deeply about keeping the plant running and providing people electricity, especially in the dead of winter.
The complete Industry News section from the August 2013 issue of Power Transmission Engineering.
Everything started in 1800 when Volta developed the first DC battery. Faraday used the DC battery to develop the first electric motor. It used brushes to transfer the battery voltage and current to the rotating disk rotor. This was in mid-1831. Thus was born the brush DC motor.
The purpose of DC motor protection is to extend a motor's lifespan by protecting it from conditions that can damage the motor's windings--both electrically and mechanically.
Novatorque energy efficient motors, Portescap smaller-size brushless DC motors, Pittman customized motors, Kollmorgen stainless steel motors, Crouzet expanded motor series, and a report from IHS on rare earth mineral supply.
The mechanical components of your drive system play a major role in overall system efficiency. Don't cut corners.
Power transmission and motion control companies will be on-hand during Hannover Messe 2013 to display the latest technology offerings in key product categories including roller bearings, gears, pumps, motors, transmissions, drive system components, clutches and braking systems.
Our product focus includes the latest technology in gears and gear drives from the leading manufacturers.
Hydrostatic drive concept gives LinsiTrak flexibility and versatility.
This paper will look at the solutions that current drive and motor technology can offer in not only improving tension control but also solving several other issues that are inherent to systems with high ratio gearing.
Power Transmission Components from Forest City Gear, Kaydon Bearings and Maxon Motors help power NASA's Curiosity Mars Rover.
Gear drives deliver power to industrial equipment such as bulk material conveyors, mixers, pumps and paper mills. The reliability that translates into greater uptime and profitability begins by specifying and selecting the proper drives for these critical applications.
Beverage industry conveyor pours on advantages in distribution center. Case study describes the new conveying systems at Motion Industries Canada.
This article presents the first kW-Class, 3-phase GaN-based inverter. Hard-switched at 100-kHz PWM, its heart is a 6-in-1 power module with 600-V GaN power HEMTs, achieving a new efficiency of 98.5%, a more than 2% improvement.
Even when the critical components of industrial power transmission gear drive systems are properly designed, specified and manufactured consistent with application requirements, performance problems can develop over time and failure may follow.
All major manufacturers of 3-phase AC induction motors offer "inverter-duty" or "inverter-readyâ models, but while these motors have inverter-rated insulation to protect the windings, the bearings--their most vulnerable parts--are too often ignored.
The complete Industry News section from the August 2012 issue of Power Transmission Engineering.
Finite Element Analysis (FEA) software can be used for a variety of mechanical engineering tasks, including injection molding simulation of plastic parts, analysis of aerospace components, impact and crash analysis of automobiles and the electromagnetic analysis of motors, actuators, transformers and sensors.
Defined in rudimentary terms, an electric motor is a device that uses electricity to create mechanical force. But in 1834, when our story takes place, most people would have trouble understanding the ramifications. That was the year that one of the earliest DC electric motors was invented—by a blacksmith.
Fairchild International, a U.S.-based manufacturer of underground mining equipment, has produced battery-powered DC scoops since the early 1980s. With 17 different models available, Fairchild offers a size to fit any coal mining operation, making it the leader in the industry.
Regardless of where you do business, when discussing, analyzing or worrying about âœThe Economyâ these days, youâ™re not thinking Main Street - youâ™re thinking global. With that stipulation, it is also accepted wisdom that quality products and sharp pencils are not enough to be and remain competitive. Accordingly, everyone is looking for an edge, an advantage, in order to beat back - or at least keep up with - the competition.
The complete Product News section from the June 2012 issue of Power Transmission Engineering.
A new preventive maintenance program at a leading New England Ivy League university demonstrates how the push for more sustainable "green" building management has led to a growing awareness of a chronic, widespread problem with HVAC motors—electrical bearing damage and failure.
The use of motor structures which can concentrate magnetic flux allows ferrite PM motors to achieve performance and power densities that approach those of PM motors using rare earth magnets, but without the cost penalties and supply source concerns of rare earth magnets.
The complete Product News section from the February 2012 issue of Power Transmission Engineering.
In looking for potential opportunities to reduce energy consumption via the drive system, a number of areas should be considered.
Compact loaders are employed where large machines have no access or are over dimensioned. New hydrostatic drives from ZF meet the demanding needs of this market.
SPS-IPC Drives 2011, which took place in Nuremburg, Germany in November, covered all components down to complete systems and integrated solutions in the electric automation industry.
The complete Product News section from the December 2011 issue of Power Transmission Engineering.
The demand for stepping motors with high efficiency and low losses has been increasing right along with the existing focus on high torque. The selection of the most suitable grade and improvement in the fastening of the laminated cores has reduced losses significantly at their peak when compared to conventional stepping motors.
The complete Industry News section from the October 2011 issue of Power Transmission Engineering.
This article is designed to help describe the selection process of a reducer to be used in the parcel handling industry. It will go over the different applications for which gearboxes are used throughout parcel handling facilities such as UPS, FedEx and DHL.
Synchronous motors controlled by variable speed drives are bringing higher efficiencies to industrial applications.
A new solution has been developed around the use of microprocessor-controlled prostheses. Just like natural limbs, these can react automatically, adapting to the current situation.
Given that many different hydraulic systems recommend the use of either frequency converters or cyclic control (soft starter technologies), the question must be asked - Which one of these solutions is the most cost-effective in reducing energy consumption and providing the most satisfactory payback time?
The obsolescence of materials and processes in the manufacture of traditional DC brush gearmotors has necessitated the development of an upgraded DC brush gearmotor.
The latest in motors technology from leading manufacturers.
Q&A with Harald Poesch, product marketing manager for servomotors at Siemens Drive Technologies.
While safety functions have been integrated into drives packages for some years now, the current trends are very exciting, from many angles. Today, a full complement of safety functions can be implemented at the front-end of a system design on all types of production machines, including printing, packaging, converting, materials handling and other equipment used throughout American industry.
The Baldor Reliance RPM AC Cooling Tower Direct Drive Motor is designed exclusively for the cooling tower industry. This motor combines the technologies of the power-dense, laminated frame RPM AC motor with high performance, permanent magnet salient pole rotor designs.
The primary driver of an airport baggage handling queue conveyor must be able to operate under increasingly demanding operating conditions, including frequent starting and stopping. The selection of the primary driver of the queue conveyor is dependent on multiple criteria, including dimensional requirements and durability characteristics.
Energy-challenged industries--and countries--can benefit from improved motor design and materials.
In this special news section, the editors of Power Transmission Engineering have gathered the latest product news and information from the gears and gear drives sector.
Maxon upgrades tissue removal system for Interlace.
During the qualification campaign of the NIRSpec (near-infrared spectrometer) instrument mechanism, the actuator could not achieve the expected lifetime that had been extended during the development phase. The initial design could not be adapted to the requested number of revolutions during that phase. Consequently the actuator needed to be modified so that the function of the mechanism would not be endangered or, by extension, the overall function of the NIRSpec instrument. The modification included a change of the overall actuator designâ”internal dimensions, tolerances, materials, lubrication and assembly processâ”while keeping the interface to the mechanism, mass and function.
One of the driving forces behind the industrial revolution was the inventionâ”more than a century agoâ”of the electric motor. Its widespread use for all kinds of mechanical motion has made life simpler and has ultimately aided the advancement of humankind. And the advent of the inverter that facilitated speed and torque control of AC motors has propelled the use of electric motors to new realms that were inconceivable just a mere 30 years ago. Advances in power semiconductorsâ”along with digital controlsâ”have enabled realization of motor drives that are robust and can control position and speed to a high degree of precision. The use of AC motor drives has also resulted in energy savings and improved system efficiency. This paper reviews the development and application of inverter technology to AC motor drives and presents a vision for motor drive technology.
The latest offering by machine design experts J.R. Hendershot and T.J.E. Miller is an 822-page brushless permanent-magnet (PM) machine design book that serves as a worthy follow-up to their 1994 work.
In order to make better purchasing decisions about centrifuge applications, one must understand the concept of centrifuges and the drives that operate this equipment.
Permanent-magnet, synchronous-torque motors offer significant advantages on high-energy-consuming and high-dynamic applications.
This paper describes the development of an educational program centered on electric motor and electric vehicle technology at the MIT (Massachusetts Institute of Technology) Edgerton Center.
The SMMA â“ Motor and Motion Association is ditching the slickers and galoshes for this yearâ™s Spring Management Conference, themed âœAfter the Storm: Navigating in the New World.â
Our politicians in Washington continue dithering over the Obama administration energy bill aimed at developing alternative, green sources of energy production. As a result, when this country will have a viable energy program in place is anyoneâ™s guess, given the usual D.C. gridlock. And yet, Americans can take more than cold comfort in the fact that at least some government agenciesâ”U.S. Department of Energy (DOE)â”and the private sectorâ”some major manufacturersâ”are doing more than their share of work in trying to harness our existing, fossil-based energy sources in such a way that they are used to their best efficiencies.
motors with premium efficiency counterparts presents businesses with a significant opportunity to reduce operating costs. A comparison between premium and standard efficiency motors from 0.25 to 10 horsepower is conducted; comparisons of full-load efficiencies are shown, and estimated payback periods are calculated. Methods for calculating the yearly kilowatt-hour consumption and yearly cost savings of premium efficiency motors for this horsepower range are also given. The cost advantages of premium efficiency motors are summarized, and relevant examples of real world cost savings are shown.
Much of the industrial energy being consumed by systems is wasted through inefficiency. For this article, a system will be defined as the following components working together: electrical input power, variable frequency drives, induction motors, gearboxes and transmission elements (chains, belts, etc.).
In keeping with a national push to bring greater energy efficiency to wastewater treatment plants, a Pennsylvania facility used data loggers to analyze motor utilization, a first step toward cutting energy costs and meeting environmental rules.
An exploration of direct drive motor trends and examples of design uses for direct drives as replacements for gear drives or belt drives.
Sunnen grows product portfolio with motion control solution from Siemens.
Servo system from Bosch-Rexroth helps create more efficient beverage palletizer.
Typically, zoo safari rides consist of cramped trams that take guests five miles-per-hour past various exhibits. You might catch a bear sleeping, hear scripted, narrated fun facts or be somewhat entertained by eccentric tour guides, but thereâ™s never much to look at except concession stands or souvenir shops.
If youâ™re replacing your belts more than once per year, itâ™s time to analyze your drive. From belt crimping damage to high belt installation tension to sprocket misalignment and adverse environmental conditions, this guide walks you through how to identify the reasons behind premature failure and makes recommendations on corrective and preventive measures.
Bosch Rexroth assists Bell-Everman with linear actuator development.
The recent trend toward using segmented laminations as a means to increase slot fill and facilitate automated fabrication of electric machines comes with a penalty of increased core loss at the segment joints.
The complete product news section from the June 2009 issue of Power Transmission Engineering.
The Royal Danish Theatre has occupied the heart of Copenhagen for centuries and recently upgraded to a new control system featuring Sprint Electric DC drives to extend the lives of the existing motors, keeping replacement costs down. The Swedish stage design and technology company Visual Act retained most of the original motors and mechanics while providing a much-needed facelift to the stage.
Presented is a high-phase, order-induction motor drive for use in a series hybrid architecture. This solution overcomes numerous compromises in current hybrid powertrain designs. Notably, it allows for a vehicle that is competitive in terms of performance and cost.
The demand for stepping motors with high efficiency and low losses has been increasing, although the demand had been previously focused on high torque. Also, the selection of the most suitable grade of lamination for improvement in fastening of the laminated cores has reduced losses significantly at their peak, when compared to conventional stepping motors. Lowering the losses of the motor has enabled continuous operation that was previously impossible. An expansion of the stepping motorâ™s usage into applications where another motor has been used for continuous operation and other usesâ”due to the heat generation problemâ”can now be pursued. In addition, these motors are very effective for energy saving. This paper explains the technology used for lowering the iron losses of the stepping motor.
Few industries are experiencing change quite as fast as the packaging arena. Lighter-weight containers are being introduced to reduce costs and energy use, packaging is being redesigned to attract consumer attention and manufacturers are using fewer materials in an effort to address environmental concerns.
The federal government estimates that manufacturing uses about one third of the energy consumed in the U.S., so manufacturing companies can play an important role in building a sustainable future.
In this paper, Edward Hage, founder of specAmotor.com, an online motor calculation and selection tool, focuses on the overheating of electric motors. Presented here is a calculation method with which the temperature and heat development of a direct current (DC) motor and a brushless motor can be predicted accurately.
Can direct drive technology improve your bottom line? Manufacturers relying upon drive systems in their production process have long sought ways to improve gearbox efficiency. While a gearbox-driven system has been the mainstay for manufacturers, it has also been, among other things, the source of frequent breakdowns, expensive line stoppages and increasingly costly maintenance.
The complete product news section from the October 2008 issue of Power Transmission Engineering (PTE).
CEE/NEMA repair-or-replace campaign saves energy, dollars and downtime.
OEMs can minimize the cost of ownership by using highly efficient motors and recognizing when unreliable motors are driving up the operating costs of their applications.
The repair-versus-replace decision is quite complicated, depending upon variables such as rewind cost, severity of the failure, replacement motor purchase price and other factors.
Calling on engineers and maintenance power plant personnel, industrial users of low- and medium-voltage motors and generators and motor repair shop staff...
The question is whether or not a customer can save time and money using a step motor. It is followed by another on the differences between brush and brushless motors...
Entrust enlists Advanced Machine & Engineering for 7-axis, 2-spindle performance.
Brevini Power Transmission helps spectators enjoy stadium sights and sounds.
The complete Industry News section from the February 2008 issue of Power Transmission Engineering
KD-Rig Puts Accelerating Developments International in Limelight
News from around the Industry
Th e total U.S. electric motor base exceeds 100 million motors and consumes more than 50% of all electricity generated in the country. Small motorsâ”fractional horsepower to 20-hpâ”comprise 99% of the motor population but consume only 25% of all generated electricity (Refs. 1,3,10,14).
Todayâ™s newspaper advertisers demand vibrant, attractive color printing, and newspaper printers are constantly looking for methods to improve printing processes to meet these demands. When it comes to improving the printing process, the key component is to choose the right printing press.