Articles About load types
Articles are sorted by RELEVANCE. Sort by Date.
With so many load types and motor types, there are many ways to couple a motor to a load.
The load carrying capacity of gear transmissions depends strongly on design, material and operation conditions. Modern analysis methods, e.g. finite element analysis (FEA), consider the above parameters with more or less sufficient accuracy. Yet it remains an ongoing challenge to account for backlash and manufacturing errors, despite a definite need to do so.
As the old adage goes, "There is more than one way to skin a cat." In the early stages of any project, system designers are faced with choices; whether they are designing a new application or retrofitting an old one, they need to determine what is the most efficient, economical and practical way of completing the task at hand. Though there are usually at least two viable means to accomplish the task, the first step is always to review and weigh the merits of each option.
The load carrying capacity of spur gears may be calculated by ISO 6336 using influence factors. The face load factor considers the impact of the non-uniform load distribution over the face width. Even if the gears had perfect geometry, the load would not distribute uniformly along the contact lines. The face load factor depends on deformations of all parts of the containing gearbox and mainly of the teeth, gears and shafts as well as on manufacturing and assembly deviations.
The main function of rolling bearings is to support load and transmit rotational movement with minimum energy loss. In order to achieve this, bearings are manufactured with particularly good quality fatigue resistance materials, proper design and tight manufacturing tolerances. Particular emphasis is put in both the macro, and micro geometry of the working shapes and surfaces of the raceways. Rolling bearings come in many types and sizes as ball and roller bearings for radial and thrust loads.
In most cases, industrial power transmission calls for flexible rather than rigid couplings in order to forgive minor shaft misalignment. For that reason, this article will focus solely on the selection of flexible couplings.
Considering the local flank parameters, such as pressure or transmission error, a significant influence of the load-dependent center distance can be observed. With the FVA-Workbench, the load-dependent center distance is always considered.
Standardized calculation methods such as ISO 6336 and DIN 3990 already exist to determine the load distributions on gears inside a planetary gearbox, but by their very universal nature, these methods offer varying results depending on the gearbox design. Double helical gears, in particular, can benefit from more specific, complex algorithms to reach a maximum level of efficiency. Double helical gears interact with the rest of the gearbox differently than helical or spur gears, and thus benefit from different analytical models outside the standardized methods. The present research project describes the algorithm to determine the load distribution of planetary gearboxes with double helical gears.
Power Transmission Engineering is collaborating with the Bearing Specialists Association (BSA) on a special section within the magazine. Bearing Briefs will present updated reports on bearing topics for each issue in 2016. Complimentary access to all BSA Bearing and Industry Briefs is available on the BSA website at www.bsahome.org/tools.
Even when the critical components of industrial power transmission gear drive systems are properly designed, specified and manufactured consistent with application requirements, performance problems can develop over time and failure may follow.
This paper is intended to enlarge the application range of radial cylindrical roller bearings by means of a more precise determination of thrust load capacity and more cost-effective design.
Many of us have been there; the bearings had the correct preload. You know it, you were there, and you personally saw the measurements. Now, the testing is done and the preload is gone. Not a little gone, not sort of gone - gone, gone. Finger pointing ensues. Suppliers are dragged in by their wrinkly Polo collars. You know the drill. Losing preload in a tapered roller bearing (TRB) system over the life of your application can be a troublesome problem, particularly for gear sets that are prone to noise or severe applications that rely on a very rigid and stable system.
Beginning with a brief summary and update of the latest advances in the calculation methods for worm gears, the author then presents the detailed approach to worm gear geometry found in the revised ISO TR 10828. With that information, and by presenting examples, these new methods are explained, as are their possibilities for addressing the geometrical particularities of worm gears and their impact upon the behavior and load capacity of a gearset under working conditions based on ISO TR 14521 âÂ€” Methods B and C. The author also highlights the new possibilities offered on that basis for the further evolution of load capacity calculation of a worm gearset based on load and contact pressure distribution.
When comparing bearing suppliers, engineers are often left with few options other than to compare dynamic load ratings and corresponding life calculations. Of course, we can look at steel and manufacturing quality; but if we are comparing sources of similar quality, those items may not provide a large contrast. It often surprises people to learn that bearing capacities are calculated values, not tested values. Lately, however, a trend is emerging for bearing suppliers to increase their ratings for higher performance bearings that have premium features such as higher quality steel and specilaized heat treatment. Bearing companies are under intense competitive pressure to make every feature add to the dynamic capacity of their bearings because it is very well understood that an increase in capacity adds to the bottom line.
Varying installation requirements for worm gears, as, for example, when used in modular gear systems, can necessitate grease lubrication - especially when adequate sealing for oil lubrication would be too complex. Such worm gears are being increasingly used in outside applications such as solar power plants and slew drives. While knowledge about the operating conditions is often appropriate, the basic understanding for load capacity and efficiency under grease lubrication is quite poor. Investigations done at FZG and sponsored by FVA/AiF are shown here to give an impression of the basic factors of load capacity and efficiency. The results of the investigation indicate a satisfying quality of calculations on heat, load capacity and efficiency based on characteristic parameters of the base oil with only slight modifications to the methodology known from DIN 3996 or ISO TR 14521.
In case you missed them, following are three recent blog postings by our popular PTE bearings blogger - Norm Parker. We also felt that, should you not be a blog follower, this would be a good way to introduce you to Norm's bearings wisdom. Parker is currently the global senior specialist/roller bearings at Fiat Chrysler Automobiles (FCA).