Radial Lip Seals
Articles About Radial Lip Seals
Articles are sorted by RELEVANCE. Sort by Date.
The improvement of the energy efficiency of industrial gear motors and gearboxes is a common problem for many gear unit manufacturers and end-users. As is typical of other mechanical components, the radial lip seals used in such units generate friction and heat, thus contributing to energy losses of mechanical systems. There exist today simulation tools that are already helping improve the efficiency of mechanical systems â” but accurate models for seal frictional losses need to be developed. In this paper SKF presents an engineering model for radial lip seal friction based on a physical approach.
Sustainability is becoming one of the most important aspects within the power transmission business. Users demand low-maintenance drive systems with as little disruption as possible, and expect lifetimes of more than 10,000 hours. Approximately 40 percent of long-term gearbox leakages can be traced back to poor interaction between the radial shaft seal (RSS) and the lubricant. Thus, it becomes essential to analyze the tribological system as a whole, which includes the gear oil, seal grease (if required), elastomer material and design, and the shaft.
SKF Product Investigation Center Troubleshoots Critical Rotating Equipment Applications with Analysis, Research and Testing Procedures.
conveying system on the varnishing line for a manufacturer of high-end kitchen cabinets were leaking. Oil was dripping on the cabinet parts â” ruining the finish. Why were half of the gearboxes leaking?
U.S. manufacturers, such as food processors, face an unprecedented competitive environment and must look for ways to be profitable without negatively affecting the quality of finished products.
Equipment downtime and reduced component life are a few of the consequences â” and potential costs â” of using the wrong seals on many types of industrial equipment including pump bearing frames, electric motors, fans, pillow blocks, gearboxes and more. However, if correctly specified and installed, seals provide effective barriers that both retain lubricants as well as protect against water, corrosion, debris and other contaminants.
Custom PEEK Compounds have led to the development of transmission seals and thrust washers that offer lower wear, friction and temperature advantages.
The complete Industry News section from the December 2019 issue of Power Transmission Engineering.
Iâ™m building a custom gearbox with 7075 T-6 spur gears, and Iâ™m concerned that aluminum flakes will enter the races on the roller bearings (SKF 2307) and cause premature failure. So my question is â” should I place an oil seal on the shaft first to protect the bearing â” or is this an unfounded concern and I should mount the seal in the typical manner outside the bearing? Or both? Or go with a sealed bearing? Iâ™m confused and could use your expertise, please.
Latest Sealing Technologies Offer Optimum Wear and Frictional Characteristics.
Seal design engineers and end users are continually seeking improved sealing systems and materials. This paper describes the potential of a new thermoplastic polyurethane (TPU) material to deliver improvements in pressure, speed and temperature capability, which are presented as comparisons to proven industry standard materials. Performance is demonstrated by virtue of test bench results of seals made from MDI-, PPDI- and NDI-based materials.
The complete Product News section from the February 2008 Power Transmission Engineering.
At first glance, ball bearings are relatively simple mechanisms. However, an analysis of their internal geometries reveals that they are quite complex. For example, the ball to raceway conformity, the radial play, and the number of balls all impact the ability of a ball bearing to support loads under a variety of conditions.
The complete product news section from the April 2010 issue of Power Transmission Engineering.
Th e primary sources of bearing failure are lack of lubrication and contaminant ingress. Industrial sealing devices are the primary protection against bearing failure. When the sealing device fails, bearing failure is imminent. Th erefore, extending the life of sealing devices extends bearing life and in turn improves equipment uptime.
The following news items offer the latest on lubrication and seal technology in the power transmission market. From bearing greases to high-performance seals, these products will help extend the service life and manufacturing capabilities for a wide range of industrial sectors.
In an industrial application, equipment uptime is vital for on-time performance and profitability. The rotating members of industrial machines are subject to the highest degree of wear and are more susceptible to failure than non-moving parts. Bearing surfaces are the most critical and often the most expensive portion of the rotary assembly; it is imperative to protect these components. The primary protector of these components is the industrial seal.
For either brand-new motors or those already in service, "best practices" means that informed technicians can make use of the latest diagnostic techniques (vibration analysis, thermography, shaft-voltage testing, etc.) to prevent electrical bearing damage -- either at the very beginning or very quickly thereafter. If done correctly, the work need only be done once.